How To Repair Detergent Dispenser In Countertop
If you have been struggling to remove your old lather dispenser-you have come to the right place. Replacing your sink-mounted soap dispenser would be a rather easy repair if it were not for over-built fixtures of the past that used large finely-threaded brass nuts that were torqued tightly. I had actually tried to remove this once to see how large the hole was but abandoned the idea when I couldn't get the nut to budge. Now I have to remove it. This repair barely warranted a write-upward if I had non ran across one play a trick on that made the repair MUCH easier. If you don't believe me, cheque out these reader comments:
Oh, thank y'all thank you thank you! I have been fighting with this thing for hours, and I fifty-fifty went to the hardware store to get another tool. That yet didn't piece of work. Then I looked and looked on youtube for a useful video. Nothing. So I saw your repair. Blindside. Done in x seconds! –Sara
Hither'south another Grandma that you've helped! … Your trick worked in 10 sec. flat! … I am doing the happy trip the light fantastic toe. Thanks a million! –Diana
Honestly, you saved me countless more hours wrestling with this thing underneath the sink. Thank you! –Rick
How to Replace a Sink-Mounted Soap Dispenser Without Putting a Wrench on the Nut
Tools Needed:
- Channel Lock Pliers
Parts Needed:
- chrome soap dispenser
- Scotch-Brite Scrub Sponge
(to make clean the sink earlier installing the new soap dispenser)
The only reason I'm replacing ours is considering the tip has corroded to the bespeak where it is very sharp:
 |
| The underneath side of the dispenser was corroded and very sharp |
Step 1: Pick a replacement sink-mounted soap dispenser.
You lot need to consider whether you want a nickel (brushed) look or chrome. Our sink (was) chrome but it looks a bit brushed with age but I went with a chrome soap dispenser from amazon.com
 |
| Delta RP1001 Sink Mounted Soap Dispenser |
Step two: Remove your old lather dispenser.
The just thing that stands in your way is the nut on the back. Most modern lather dispensers have a nylon nut that is intended to be installed and uninstalled by mitt but mine had a brass nut on it and was near incommunicable to accomplish upwardly there, see where I was working, and loosen the corroded thing:
 |
| The onetime soap dispenser with a tightly torqued contumely nut (excuse the poor focus) |
Our cabinet has a shelf under the sink so it makes accessing this nut very difficult with the only tool I actually have to loosen it, a channel-lock wrench:
 |
| The quondam soap dispenser under our sink (don't enquire what those 2 capped drains are sticking out of the wall–I didn't plumb this firm) |
I tried and tried but I couldn't run across the nut and reach my arms upwards in there to get the wrench on that nut and and so it occurred to me that at that place was an easier way since I was replacing the current lather dispenser.
Step 3: The Fob—put a wrench on the acme of the soap dispenser fixture.
Because we are throwing away the current fixture we can simply put a wrench on the top of the fixture to break loose the nut. Turn it counter-clockwise to loosen:
 |
| The Trick–put your wrench on the meridian to break gratis the nut. |
In one case I broke loose the nut past putting the wrench on the summit I was able to unscrew the nut from below using my fingers. Information technology was quite uncomfortable property the top and unscrewing the nut from below at the same time but I have long arms–you might need to put a vice grip (or a friend) on the height to concord it nevertheless. In that location was a bunch of caked-on soap and corrosion on the threads and then information technology made difficult turning.
Footstep 4: Clean the sink.
Earlier installing the new soap dispenser make certain to clean the sink around the pigsty:
 |
| Corrosion where the former lather dispenser was located. |
Carefully make clean the area using a scotch-bright scratchy sponge (scrub in the direction of the grain on the stainless steel). Mine cleaned up nicely:
 |
| Nice and clean for the new soap dispenser. |
Step 5: Install the new lather dispenser.
Take off the bottle and so the nut. Make certain the rubber washer stays on top.
 |
| Nut removed from the new soap dispenser |
You only demand to manus tighten the nut. make sure you put the flat side up (towards the sink lesser).
 |
| Underneath view of the newly installed sink mounted soap dispenser |
Step vi: Spiral on the new bottle.
I tend to plough things like this backwards until I experience/hear the threads jump downward (indicating you are ready to start) and so plow it tight. It helps you continue from cantankerous-threading nuts. This bottle is pretty flimsy and then you don't want to tear it up.
 |
| The soap bottle installed |
Step 7: Fill up with lather and finish the dishes.
The dispenser I purchased came with a funnel merely I simply shoot the soap direct into it without, no funnel necessary. Yous could take the canteen off and fill up it but it'southward a pain to get it back on and similar I shared before, the bottle is not made of thick plastic so I would install it and leave information technology solitary (and it should serve you simply fine that way). Mission accomplished.
Amazon Associate Disclosure: As an Amazon Associate I earn from qualifying purchases. This ways if you click on an affiliate link and purchase the item, I will receive an affiliate committee. The price of the detail is the same whether it is an chapter link or non. Regardless, I just recommend products or services I believe will add value to Share Your Repair readers. By using the affiliate links, you are helping back up Share Your Repair, and I genuinely appreciate your support.
Source: http://www.shareyourrepair.com/2014/01/how-to-replace-a-sink-mounted-soap-dispenser-without-putting-a-wrench-on-the-nut.html
Posted by: cordovaworythe1986.blogspot.com
0 Response to "How To Repair Detergent Dispenser In Countertop"
Post a Comment